Menu
Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Search
Search titles only
By:
Search titles only
By:
New posts
Search forums
Search
Search titles only
By:
Search titles only
By:
Menu
Welcome DJI Spark Pilot!
Jump in and join our free Spark community today!
Sign up
Forums
DJI Spark Forums
Spark Help
sequence with OTG
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Criptix" data-source="post: 48051" data-attributes="member: 1895"><p>Someone posted this. </p><p>I use it with no errors. </p><p></p><p>My OTG procedure (DJI GO 4 4.2.12):</p><p></p><p>1. Turn on Remote Control (RC). Wait for solid red.</p><p>2. Plug in OTG cable in phone.</p><p>3. Plug other end in RC.</p><p>4. Choose DJI GO 4 app in popup window.</p><p>5. Wait until GO 4 app is open and it says "RC Connected" in lower left corner.</p><p>6. Power up your Spark. Try to place RC as close to Spark as possible. (DJI recommend 20 cm)</p><p>7. Bonding between RC and Spark should take less than 30 sec.</p><p>8. Hit GO FLY!</p><p></p><p>This is absolutely fail-safe method!</p><p></p><p>If for some reason you want to change channels, lower numbers is 2.4 GHz and higher numbers is 5.8 GHz.</p><p>In CE area 2.4 GHz channel is preferred.</p><p></p><p>To change between bands/channels:</p><p></p><p>9. In Wifi section of settings, choose "Custom".</p><p>10. Where it says Channel Index, tap one of the channels.</p><p>11. Tap "Apply" at the bottom of the page.</p><p>12. Power down your Spark (Air-craft)</p><p>13. Power up your Spark again.</p><p>14. Within 30 sec you will see new channel has been set.</p><p></p><p>This is also fail-safe method!</p><p></p><p>FLY SAFE!</p></blockquote><p></p>
[QUOTE="Criptix, post: 48051, member: 1895"] Someone posted this. I use it with no errors. My OTG procedure (DJI GO 4 4.2.12): 1. Turn on Remote Control (RC). Wait for solid red. 2. Plug in OTG cable in phone. 3. Plug other end in RC. 4. Choose DJI GO 4 app in popup window. 5. Wait until GO 4 app is open and it says "RC Connected" in lower left corner. 6. Power up your Spark. Try to place RC as close to Spark as possible. (DJI recommend 20 cm) 7. Bonding between RC and Spark should take less than 30 sec. 8. Hit GO FLY! This is absolutely fail-safe method! If for some reason you want to change channels, lower numbers is 2.4 GHz and higher numbers is 5.8 GHz. In CE area 2.4 GHz channel is preferred. To change between bands/channels: 9. In Wifi section of settings, choose "Custom". 10. Where it says Channel Index, tap one of the channels. 11. Tap "Apply" at the bottom of the page. 12. Power down your Spark (Air-craft) 13. Power up your Spark again. 14. Within 30 sec you will see new channel has been set. This is also fail-safe method! FLY SAFE! [/QUOTE]
Verification
Post reply
Forums
DJI Spark Forums
Spark Help
sequence with OTG